Stained Glass Leaded Window Fitting Tips: Expert Installation Advice

Installing a leaded glass panel requires care and precision. By following the correct fitting steps, you can achieve a strong, attractive, and long-lasting result. Whether you are fitting a single or double-glazed unit, this stained glass installation guide provides practical tips for a successful installation.

If you are unsure about any part of the process, consider hiring a professional installer to ensure a secure and accurate fit.

Handling & Safety Tip: Always handle your new www.onglass.co.uk toughened glass panel with care and store them safely during installation. Do not place the glass directly on concrete, tile, or other hard surfaces, as this can chip the edges or cause the panel to shatter. Instead, rest the glass on a piece of carpet, thick cardboard, or a clean wooden block to protect it from damage.

Maesuring Guide


How do I remove wooden glazing beads or old putty?

Before you start, cover the old glass on both sides with strong sticky tape or parcel tape. This is an important safety step. If the glass cracks or breaks while you remove it, the tape will help hold the pieces together and reduce the risk of sharp shards falling.

Next, run a sharp utility knife along the paint line to break the seal between the frame and the wood glazing beads. Then, use a thin chisel or putty knife to gently prise the wooden beads away from the frame. Work slowly and carefully to avoid splitting the timber, and label each bead so you can refit it in the same position later.

If your window has traditional glazing putty instead of beads, score around the edge with a knife before carefully removing the hardened putty with a putty knife or glazing chisel. For very hard putty, use a heat gun on a low setting to soften it. Keep the heat moving to avoid scorching the timber.

Finally, remove any old glazing pins, loose putty, paint, or debris from the glazing rebate. A clean, smooth rebate will help your new stained glass panel fit securely and make installation much easier.

A Step by Step Stained Glass Fitting Guide for Single Glazed Panels

When installing a single-glazed glass panel into a wooden frame, we recommend using glazing foam strip instead of traditional putty or silicone.

Apply a 10mm x 4mm single-sided adhesive foam strip to the frame rebate where the glass meets the timber. You can also apply foam tape to the wooden glazing beads.

This foam sandwich method cushions the glass and holds it securely in place, helping to reduce stress and improve durability.

  • Why use foam strip? First, it is incredibly quick, clean, and easy to use.
  • Affordability: Furthermore, you can conveniently purchase glazing foam strips online for just a few pounds.

How to Fit a Double-Glazed Leaded Glass Panel into a Wood Frame

When fitting a double-glazed unit into a wooden frame, use the same glazing foam sandwich method as for single glazing. However, extra protection against water ingress is essential if the window is external.

Moisture can damage timber frames and shorten their lifespan of any double glazing. Water trapped at the bottom of the frame can cause the double-glazed unit to fail, leading to condensation and misting between the panes.

To prevent these problems, follow these key steps:

  • Create Drain Holes: , Drilling drain holes in the bottom of the frame will allow any trapped water to escape easily.
  • Use Glass Spacers: Additionally place spacers in the bottom of the frame underneath the double glazed leaded glass panel. This lifts the panel slightly and effectively stops moisture from becoming trapped.
  • Apply Silicone Sealant: Finally, run a small line of silicone around the outside edge where the glass meets the wood. This simple step creates an extra barrier against water penetration.
  • Top Tip: Use masking tape on the leaded glass panel and frame. This will give you a nice clean line of sealant without the mess.

Stained Glass Fitting Guide: How to Fit a Double Glazed Leaded Unit into a PVC Frame

Installing or replacing a double-glazed leaded unit in a uPVC frame requires a different method than fitting one in a timber frame. With the right tools and fitting techniques, you can achieve a secure, level, and weatherproof installation.

If you are unsure about any part of this stained glass fitting guide, we recommend hiring a professional window fitter to ensure a safe and accurate installation.

Step 1: Remove the Beading Safely

To begin, you will need to remove the plastic glazing beads holding the old unit in place.

  • Use the Right Tool: Always use a dedicated bead removal tool, a stiff, thin-bladed putty knife, or a specialised Don Carlos knife. Avoid using screwdrivers, as they can easily gouge and permanently damage the PVC plastic.
  • The Technique: Gently insert the blade into the seam between the bead and the main frame, right at the center of the longest length. Pry gently until the bead pops out of its channel. Repeat this for all four sides, removing the top bead last to prevent the glass from falling forward unexpectedly.
  • Older Plastic Beads: If older plastic glazing beads prove difficult to remove, you can carefully remove the small black rubber gasket first. Take care not to damage it, as you may wish to reuse it. In some cases, the gasket may have perished with age and can be difficult to replace with a modern equivalent.
  • Top Tip: Use masking tape to label the beads, Top, Bottom, Left, and Right. This guarantees you snap them back into their original sides perfectly.

Step 2: Clear the Drainage Paths

Before fitting your new leaded glass panel, inspect the bottom channel of the uPVC frame.

uPVC windows have built in drainage systems that allow water to escape. Check that the drain holes are clear of dust, plastic offcuts, and other debris.

Blocked drain holes can trap water inside the frame, which may cause the double glazed unit to fail or develop condensation between the panes over time. The duct tape place around the edge of a double glazed unit can also cause water to be trapped and even track back into the inside of the window.

Step 3: Position the Unit with Plastic Packers

Never sit the glass unit directly onto the flat PVC frame. Instead, you must use specialized plastic glazing packers (spacers) to correctly position the glass.

  • Square the Unit: Place the packers underneath the bottom edge to raise the unit slightly, allowing water to flow freely underneath it toward the drain holes.
  • Prevent Movement: Furthermore, place packers around the sides to keep the unit central and perfectly square. This ensures an even seal and prevents the heavy glass from shifting when the window or door opens and closes.

Once your glass is perfectly balanced, you can begin refitting the glazing beads. To make the job easier, you can gently bend the beads a little in the middle, which helps snap the ends into the frame corners first. Finally, use a soft nylon mallet to safely tap the rest of the bead into position.


Weathering and Protecting New Leaded Glass

Important Tip: Try to avoid fitting leaded glass in the rain. If the New lead gets wet immediately, it will oxidize too quickly, which often results in an unsightly white residue after a day or two.

New lead naturally needs time to weather in when exposed to the elements. This natural oxidisation process typically takes a few days or weeks to settle down. Once this period passes, the lead will maintain a stable, beautiful color.

However, if the weather forecast predicts rain right after your installation, you can protect your window. Simply apply a some patination oil or as an easy alternative a tiny amount of spray-on grease to the lead using a soft rag to shield the newly exposed metal. Be careful as the lead and glass can be easily scratched.

Leaded Glass Design Limitations: What You Need to Know

Because we handcraft everything, we can adjust and modify almost any design to fit different-sized glass panels. Nevertheless, physical limitations do exist.

For instance, a large, intricate design will not fit entirely into a small window panel. Conversely, a small design may require extra detail to properly fill out a larger piece of glass. Think of it as the difference between icing a small fairy cake with a short name like “Tim” versus a longer name like “Charlotte.” Therefore, please keep these design scaling factors in mind when you request a quote.


Obscured Glass Selection: Help & Advice

Choosing the right backing glass is essential for both privacy and aesthetics. For double-glazing projects, we highly recommend two fantastic options:

  • Minster Glass: This option offers superior privacy while delivering a timeless, traditional look.
  • Flemish Glass: In contrast, Flemish glass is more transparent and beautifully complements our water-themed designs.

We offer many more options to suit your style. Explore our designs on Pinterest for more inspiration!

Get a Free Quote Today: Contact Us

Email is the fastest and most efficient way to reach us with your inquiry. If you would like a bespoke quote, please email us at info@onglass.co.uk and include the following details:

  • Glass Dimensions: Width x height in millimeters (mm).
  • Design & Style: Please include photos or sketches if possible.
  • Quantity: How many panels do you require?
  • Glazing Type: Specify whether you need single or double-glazed panels.
  • Glass Finish: Let us know if you prefer clear or obscured privacy glass.
  • Logistics: State whether you prefer collection or delivery.



Scroll to Top